Monel Pipes & Tubes
Monel Alloys pipes & tubes supplied to ASTM B165 from our Mumbai stockyard. Monel is a nickel-copper alloy, roughly 67% nickel and 30% copper, with outstanding resistance to seawater, brine and hydrofluoric acid. It retains strength and toughness from cryogenic temperatures up to about 500°C. Monel 400 is the standard grade; K-500 is precipitation hardened for roughly three times the yield strength.
Governing Standards for Monel Pipes & Tubes
State the standard on your enquiry and we will confirm stock against it.
| Standard | Covers |
|---|---|
| ASTM B165 | Alloy 400 seamless pipe and tube |
Monel Chemical Composition (%)
Composition and mechanical values are the limits set by the governing ASTM specification and are given for reference. The mill test certificate supplied with your consignment carries the actual heat analysis.
| Element | Monel 400 | Monel K-500 |
|---|---|---|
| Nickel | 63.0 min | 63.0 min |
| Copper | 28.0 – 34.0 | 27.0 – 33.0 |
| Iron | 2.50 max | 2.00 max |
| Manganese | 2.00 max | 1.50 max |
| Aluminium | — | 2.30 – 3.15 |
| Titanium | — | 0.35 – 0.85 |
| Carbon | 0.30 max | 0.25 max |
| Sulphur | 0.024 max | 0.010 max |
Monel Pipes & Tubes Specifications
Monel Pipes & Tubes — Chemical Composition
| Grade | C | Mn | P | S | Si | Cr | Ni | Mo | Other |
|---|---|---|---|---|---|---|---|---|---|
| TP 304 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–11.0 | — | N 0.10 |
| TP 304L | 0.035 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 8.0–13.0 | — | N 0.10 |
| TP 316 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0–18.0 | 11.0–14.0 | 2.00–3.00 | N 0.10 |
| TP 316L | 0.035 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0–18.0 | 10.0–15.0 | 2.00–3.00 | N 0.10 |
| TP 321 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 17.0–19.0 | 9.0–12.0 | — | Ti ≥ 5 × C |
| TP 347 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 17.0–19.0 | 9.0–13.0 | — | Nb ≥ 10 × C |
| TP 310S | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 24.0–26.0 | 19.0–22.0 | — | — |
| TP 317L | 0.035 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0–20.0 | 11.0–15.0 | 3.00–4.00 | N 0.10 |
Note: Per ASTM A312 / A240. Values are maximum % by weight unless a range is shown. ASTM A312 permits 0.035% max carbon on L grades, where ASTM A240 plate specifies 0.030% max.
Monel Pipes & Tubes — Mechanical Properties
| Grade | Tensile Strength (min) | Yield Strength 0.2% (min) | Elongation (min) | Hardness (max) |
|---|---|---|---|---|
| TP 304 | 515 MPa (75 ksi) | 205 MPa (30 ksi) | 35% | 90 HRB / 192 HBW |
| TP 304L | 485 MPa (70 ksi) | 170 MPa (25 ksi) | 35% | 90 HRB / 192 HBW |
| TP 316 | 515 MPa (75 ksi) | 205 MPa (30 ksi) | 35% | 90 HRB / 192 HBW |
| TP 316L | 485 MPa (70 ksi) | 170 MPa (25 ksi) | 35% | 90 HRB / 192 HBW |
| TP 321 | 515 MPa (75 ksi) | 205 MPa (30 ksi) | 35% | 90 HRB / 192 HBW |
| TP 347 | 515 MPa (75 ksi) | 205 MPa (30 ksi) | 35% | 90 HRB / 192 HBW |
| TP 310S | 515 MPa (75 ksi) | 205 MPa (30 ksi) | 35% | 90 HRB / 192 HBW |
Note: Specified minimum values in the solution-annealed condition, per ASTM A312 / A240. Elongation is measured in 50 mm (2 in.).
Monel Pipes & Tubes — Size Range & Supply Condition
| Parameter | Range |
|---|---|
| Nominal bore | 1/2" NB to 24" NB (larger on enquiry) |
| Outside diameter | 6 mm to 610 mm |
| Wall thickness | Schedule 5S, 10S, 20, 30, 40 / 40S, 60, 80 / 80S, 100, 120, 140, 160, XXS |
| Manufacturing type | Seamless, ERW, EFW and LSAW |
| Length | Single random 4–7 m, double random 9–13 m, or cut to length |
| End finish | Plain end, bevelled end (30° ± 5°), threaded |
| Surface | Annealed & pickled, bright annealed, mirror or satin polished |
| Governing standards | ASTM A312 / A358 / A790 / A106 / A53, ASME B36.10M & B36.19M |
Monel Pipes & Tubes — Pipe Dimensions & Weight Chart
| NPS | OD (mm) | Sch 10S | Sch 40S | Sch 80S |
|---|---|---|---|---|
| 1/2" | 21.3 | 2.11 mm / 1.02 kg/m | 2.77 mm / 1.29 kg/m | 3.73 mm / 1.65 kg/m |
| 3/4" | 26.7 | 2.11 mm / 1.30 kg/m | 2.87 mm / 1.72 kg/m | 3.91 mm / 2.24 kg/m |
| 1" | 33.4 | 2.77 mm / 2.13 kg/m | 3.38 mm / 2.55 kg/m | 4.55 mm / 3.30 kg/m |
| 1 1/4" | 42.2 | 2.77 mm / 2.75 kg/m | 3.56 mm / 3.46 kg/m | 4.85 mm / 4.55 kg/m |
| 1 1/2" | 48.3 | 2.77 mm / 3.17 kg/m | 3.68 mm / 4.13 kg/m | 5.08 mm / 5.52 kg/m |
| 2" | 60.3 | 2.77 mm / 4.01 kg/m | 3.91 mm / 5.54 kg/m | 5.54 mm / 7.62 kg/m |
| 2 1/2" | 73.0 | 3.05 mm / 5.36 kg/m | 5.16 mm / 8.80 kg/m | 7.01 mm / 11.63 kg/m |
| 3" | 88.9 | 3.05 mm / 6.58 kg/m | 5.49 mm / 11.51 kg/m | 7.62 mm / 15.57 kg/m |
| 4" | 114.3 | 3.05 mm / 8.53 kg/m | 6.02 mm / 16.38 kg/m | 8.56 mm / 22.75 kg/m |
| 5" | 141.3 | 3.40 mm / 11.78 kg/m | 6.55 mm / 22.18 kg/m | 9.53 mm / 31.56 kg/m |
| 6" | 168.3 | 3.40 mm / 14.09 kg/m | 7.11 mm / 28.80 kg/m | 10.97 mm / 43.38 kg/m |
| 8" | 219.1 | 3.76 mm / 20.35 kg/m | 8.18 mm / 43.36 kg/m | 12.70 mm / 65.88 kg/m |
| 10" | 273.0 | 4.19 mm / 28.31 kg/m | 9.27 mm / 61.44 kg/m | 12.70 mm / 83.08 kg/m |
| 12" | 323.8 | 4.57 mm / 36.67 kg/m | 9.53 mm / 75.27 kg/m | 12.70 mm / 99.30 kg/m |
Note: Outside diameter and wall thickness per ASME B36.19M. Weight is calculated for austenitic stainless at 8.0 g/cm3 and is indicative — actual weight varies with grade and mill tolerance. Each cell shows wall thickness / weight per metre.
Monel Pipes & Tubes — Square & Rectangular Sections
| Section | Size range | Wall thickness | Length |
|---|---|---|---|
| Square | 10 x 10 mm to 200 x 200 mm | 0.8 mm to 8 mm | 6 m / 12 m / cut to length |
| Rectangular | 10 x 20 mm to 200 x 400 mm | 0.8 mm to 8 mm | 6 m / 12 m / cut to length |
| Round (welded) | 6 mm to 610 mm OD | 0.6 mm to 12 mm | 6 m / 12 m / cut to length |
| Finish | Mill, matt, satin, No. 4 brushed, No. 8 mirror | — | — |
Note: Welded stainless steel hollow sections, supplied in 304/304L, 316/316L and 202. Other sizes are rolled to order.
Monel Pipes & Tubes — Physical Properties
| Property | SS 304 / 304L | SS 316 / 316L |
|---|---|---|
| Density | 8.00 g/cm³ | 8.00 g/cm³ |
| Melting range | 1400–1450 °C | 1375–1400 °C |
| Modulus of elasticity | 193 GPa | 193 GPa |
| Thermal conductivity (100 °C) | 16.2 W/m·K | 16.3 W/m·K |
| Specific heat (0–100 °C) | 500 J/kg·K | 500 J/kg·K |
| Thermal expansion (0–100 °C) | 17.2 µm/m·°C | 15.9 µm/m·°C |
| Electrical resistivity | 720 nΩ·m | 740 nΩ·m |
| Max continuous service temp. | ≈ 870 °C | ≈ 925 °C |
| Magnetic response (annealed) | Non-magnetic | Non-magnetic |
Note: Values at 20 °C unless stated. Thermal expansion matters when austenitic stainless is welded to carbon steel.
Monel Pipes & Tubes — Equivalent Grades Across Standards
| ASTM / AISI | UNS | EN / DIN | EN Name | JIS | GB |
|---|---|---|---|---|---|
| 304 | S30400 | 1.4301 | X5CrNi18-10 | SUS 304 | 06Cr19Ni10 |
| 304L | S30403 | 1.4307 | X2CrNi18-9 | SUS 304L | 022Cr19Ni10 |
| 316 | S31600 | 1.4401 | X5CrNiMo17-12-2 | SUS 316 | 06Cr17Ni12Mo2 |
| 316L | S31603 | 1.4404 | X2CrNiMo17-12-2 | SUS 316L | 022Cr17Ni12Mo2 |
| 321 | S32100 | 1.4541 | X6CrNiTi18-10 | SUS 321 | 06Cr18Ni11Ti |
| 347 | S34700 | 1.4550 | X6CrNiNb18-10 | SUS 347 | 06Cr18Ni11Nb |
| 310S | S31008 | 1.4845 | X8CrNi25-21 | SUS 310S | 06Cr25Ni20 |
| 430 | S43000 | 1.4016 | X6Cr17 | SUS 430 | 10Cr17 |
Note: Cross-reference for enquiries written against European, Japanese or Chinese standards. Equivalents are close but not always identical — check the composition limits before substituting.
Monel Pipes & Tubes — Ordering & Supply
| Parameter | Detail |
|---|---|
| Minimum order quantity | 5 kg (mixed sizes within a grade can be combined to reach the MOQ) |
| Price basis | Ex-works Mumbai, FOB or CIF — quoted per kg, per metre or per piece depending on the form |
| Lead time | Ready stock dispatched in 1–3 working days; mill orders typically 2–6 weeks |
| Certification | Mill test certificate to EN 10204 3.1 as standard; 3.2 with third-party witness, IBR and NACE MR0175 on request |
| Testing available | PMI, IGC (ASTM A262), hydrostatic, ultrasonic, radiographic, impact and hardness testing |
| Third-party inspection | Bureau Veritas, TÜV, DNV, SGS, Lloyd's Register, Intertek, RITES and client/EPC inspection |
| Packing | Wooden crates or pallets, plastic caps on pipe ends, VCI wrapping where required, seaworthy export packing |
| Payment terms | Advance, against proforma invoice, or LC at sight for export orders |
| Supply area | Across India and export to the Middle East, Europe, the USA, Africa and South East Asia |
| Product form | Pipes |
Note: Cut lengths, non-standard sizes and special certification are available on request. Prices are quoted against grade, size, schedule and quantity.
Values shown are the specified minima and maxima published in the governing standards and are given for guidance. The mill test certificate supplied with your consignment reports the actual results for that heat.
When to specify Monel for pipe work
Choose Monel 400 for seawater handling, brine, hydrofluoric acid and alkalis, where it outperforms stainless steel by a wide margin. Choose K-500 where the same corrosion resistance is needed together with high strength and galling resistance — pump shafts, valve stems, fasteners and propeller shafts.
Products in this range
Monel in other forms
Full composition, properties and equivalents on the Monel Alloys grade page.
Frequently Asked Questions
- What is the difference between Monel 400 and K-500?
- K-500 adds aluminium and titanium and is precipitation hardened, which raises minimum yield strength from about 170 MPa to about 690 MPa while keeping essentially the same corrosion resistance. K-500 also resists galling better, which is why it is used for shafts, stems and fasteners. Monel 400 is more ductile and easier to form and weld.
- Why is Monel used for hydrofluoric acid?
- The nickel-copper composition is exceptionally resistant to HF across a wide range of concentrations and temperatures, where stainless steels corrode rapidly. This makes Monel a standard material for HF alkylation units in refineries. Always confirm against the specific concentration, temperature and aeration of your service.
Send your Monel Pipes & Tubes requirement
Give us the size, schedule or thickness, quantity and standard and we will confirm stock and send a firm price. Minimum order quantity 5 kg, mill test certificate to EN 10204 3.1 with every consignment.